Technician Answers

Kenmore 253.70413411 refrigerator door and freezer gaskets worn and torn: how to replace them

Answered by GIR Technician, GIR Appliance Repair · November 12, 2026
❓ The question
Kenmore Refrigerator Model 253.70413411 Age: 8–12 years

“I need a new door and freezer gasket for my fridge, do you have these for my model?”

My gaskets are worn and partially torn

Asked by Doug from SC · November 12, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Doug,

Torn, flattened gaskets are one of the most common wear items on a fridge this age, and the good news is they’re very much worth replacing. A bad seal lets warm, humid air in, so the fridge runs longer and the freezer frosts up. Swapping both is a straightforward DIY job.

Your model and the right gaskets

Your Kenmore 253.70413411 was made by Frigidaire (the 253 prefix tells us that), so the gaskets are Frigidaire-made parts. Each door takes its own gasket, and they aren’t interchangeable. The fresh food door gasket and the freezer door gasket are different sizes. They also come in different colors, so match the one you have now (usually white, almond or gray). I’ve listed both parts below. You can check price and availability right there, and we’ll match the exact part numbers to your 253.70413411. As a rough guide, each gasket usually runs somewhere around $40–$120 depending on the size.

How I’d replace them

  1. Unplug the fridge or turn off its breaker before you start.
  2. Warm the new gasket first. They ship folded and kinked. Lay it out flat in a warm room for a few hours, or soak the folded corners in warm water for a few minutes, so it relaxes back into shape.
  3. Peel back the old gasket along the inside edge of the door. On most Frigidaire-built doors it’s either pressed into a channel or held under a plastic retainer by screws. If you see screws, loosen them a few turns. Don’t take them all the way out, because the inner door panel can shift.
  4. Do one side at a time. Pull a section of the old gasket, slip the new one in, and move on.
  5. Snug the screws back down evenly, close the door and let it sit for a day. Small gaps usually pull in on their own. For a stubborn spot, a little warm air from a hair dryer (on low, kept moving) helps the gasket fill out.

Check the seal afterward

Close the door on a dollar bill in a few spots around each door. You should feel a light drag when you pull it out. If it slides out easily in one area, the door may be sagging rather than the gasket being bad. Check that the fridge is level side to side and tilted slightly back so the doors swing shut on their own, and look for a loose hinge.

Also give the freezer a look for heavy frost buildup. If it’s iced up from the leaky seal, defrost it fully after the new gaskets are in so it can recover.

If anything doesn’t line up or you’re not sure which gasket goes where, send a follow-up and I’ll help you sort it out.

🔧 Part needed
Refrigerator (fresh food) door gasket
Fits Kenmore 253.70413411

If the fresh food door seal is torn or won't hold a dollar bill. We'll match the exact part # to your 253.70413411.

Freezer door gasket
Fits Kenmore 253.70413411

If the freezer door seal is torn, flattened or frosting up at the edges. We'll match the exact part # to your 253.70413411.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day