Appliance Repair Tips

Miele Dishwasher Fault Codes: F11, F12, F13, F14, F70 & F78 Explained

By GIR Appliance Repair · November 16, 2026 · 8 min read
Miele Dishwasher Fault Codes: F11, F12, F13, F14, F70 & F78 Explained

Miele dishwashers are built to last twenty years, so when one stops mid-cycle and shows a fault code like F11 or F70, most owners in Houston, The Woodlands, Spring and Kingwood would rather fix it than replace it — and in most cases that is the right call. The challenge is that Miele’s codes are short and the manual explains very little. This guide translates the fault codes we see most often on Miele G-series dishwashers, explains what you can safely check yourself, what each repair typically costs, and when you should stop and call a technician.

A note before you start: Miele uses slightly different code sets across model generations, and some older or display-less models show a flashing light pattern (such as a blinking “Check inlet/drain” indicator) instead of an F-code. Always confirm the code against the manual for your exact model number, which is printed on the edge of the door.

Miele Dishwasher Fault Codes at a Glance

CodeWhat it meansCommon causesEst. Repair Cost
F11Drainage faultClogged filters, kinked drain hose, blocked sink connection, failing drain pump$0–$480
F12 / F13Water intake fault (F12 at the start of a step, F13 at the end)Water valve closed, low pressure, clogged inlet hose filter, faulty inlet valve$0–$420
F14Varies by model; most often linked to the heater pressure switch or circulation/heating circuitAir in the system after a drain problem, pressure switch, heater or pump issue$0–$500
F70Waterproof system activated: water detected in the baseLeaking hose, seal, pump or valve; excess suds from the wrong detergent$150–$450
F78Circulation pump faultDebris jamming the impeller, worn pump motor, wiring or control fault$0–$800

Cost ranges are typical for the Houston area and include parts and labor; Miele parts cost more than mainstream brands. The exact price is confirmed after diagnosis, and our $75 service call is applied toward the repair.

F11: Drainage Fault

F11 means the dishwasher could not pump water out within the expected time. It is the most common Miele code we see, and about half the time it is solved without replacing any part.

What to check yourself

  • Clean the filter combination. Twist out the filter assembly at the bottom of the tub, separate the coarse, fine and micro-fine filters, and rinse them under running water. Grease and food scraps build up fast if dishes go in unrinsed.
  • Check the drain pump cover. Under the filters, many Miele models have a small pump cover you can unclip. Bits of glass, fruit labels and pits often lodge here and stop the impeller.
  • Look at the drain hose. A hose kinked behind the dishwasher after cabinet work is a classic cause.
  • Check the sink connection. If the dishwasher drains into a garbage disposal, a new disposal still sealed with its knock-out plug, or a jammed disposal, will block it. Our garbage disposal repair guide covers that side.

When it’s a repair

If the filters and pump area are clear and the code returns, the drain pump itself may have failed or the non-return valve may be stuck. Drain pump replacement on a Miele typically runs $280–$480. For more on drainage problems in general, see dishwasher not draining and water standing at the bottom of the dishwasher.

F12 and F13: Water Intake Faults

These codes mean the machine did not receive enough water in time. Start with the obvious:

  • Make sure the water supply valve under the sink is fully open.
  • Check whether other taps in the house have normal pressure; work on the street or a recent plumbing repair can drop pressure temporarily.
  • Turn off the water, disconnect the inlet hose at the valve, and clean the small mesh filter inside the hose fitting. In areas with hard water and older pipes, this screen clogs with scale and sediment.
  • Make sure the inlet hose is not kinked or crushed.

If water reaches the machine with good pressure but the code persists, the inlet valve or the flow meter is usually at fault. Inlet valve replacement typically costs $250–$420. Our guide to dishwashers not getting water explains the intake side in more detail.

F14: Model-Dependent Fault

F14 is the code where sources disagree most. On many Miele models it relates to the heater pressure switch or the heating circuit; on others it is grouped with circulation pump faults. In practice we often see F14 appear after a drainage or intake problem left air trapped in the system. Clean the filters, run a short rinse cycle, and see whether it clears. If F14 comes back, it needs a proper diagnosis — guessing at parts on a Miele gets expensive quickly.

F70: Waterproof System Activated

F70 means Miele’s Waterproof System has detected water in the base pan under the tub and has shut the inlet valve to protect your floor. Treat this one seriously:

  1. Turn the dishwasher off and close the water supply valve.
  2. Check the floor and the cabinets on either side for water.
  3. Think back: did anyone use regular hand dish soap or too much detergent? Excess suds can overflow into the base and trigger F70 even when nothing is broken.

Do not try to tip the machine to drain the base pan unless you know the model well — it can damage the cabinet, the floor or the door hinges. A technician will find the leak source (a hose, door seal, pump seal or valve), fix it and dry the base so the float switch resets. Typical cost is $150–$450 depending on the leaking part.

F78: Circulation Pump Fault

The circulation pump pushes water through the spray arms; without it, dishes come out dirty or the cycle stops. A reset (switching off at the button and the breaker for a few minutes) may clear F78 temporarily, but it will return if the cause remains. Sometimes the impeller is jammed by debris, which is an inexpensive fix. If the pump motor or its electronics have failed, replacement on a Miele typically runs $450–$800 — still often worth it on a machine that is otherwise in good shape.

🔧 Need a professional repair?

GIR Appliance Repair serves Houston, The Woodlands & Kingwood — same-day availability.

📞 (346) 625-4289

How to Reset a Miele Dishwasher

After clearing the cause, switch the dishwasher off with the On/Off button, wait at least 30 seconds (some technicians recommend a few minutes at the breaker for persistent codes), then switch it back on and run a short rinse program. If the same code returns immediately, stop running cycles — repeated restarts with a drain or leak fault can add water to the base pan and turn a simple repair into a bigger one.

Hard Water and Miele Dishwashers in the Houston Area

Much of the Houston area, including The Woodlands, Spring and Conroe, has moderately hard to hard water. Miele dishwashers include a water softener that relies on dishwasher salt, and the water hardness has to be set in the menu to match your water. When the salt runs out or the hardness is set too low, scale builds on the heater and in the intake path, which contributes to intake faults and poor cleaning over time. Keep the salt reservoir topped up and set the hardness using a test strip or your water utility’s report.

DIY Maintenance Checklist

TaskHow often
Scrape (don’t rinse) large food scraps before loadingEvery load
Clean the filter combinationEvery 1–2 weeks
Refill dishwasher salt and rinse aidWhen the indicator lights
Check the spray arms for blocked nozzlesMonthly
Run an empty hot cycle with dishwasher cleanerEvery 2–3 months
Clean the inlet hose filterYearly, or after F12/F13

Repair or Replace a Miele Dishwasher?

New Miele dishwashers cost roughly $1,200–$2,500, and they are designed for a long service life. That means most repairs — pumps, valves, leaks and sensors — are worth doing on machines up to about 12–15 years old. Replacement starts to make sense when a very old unit needs a control module and a pump at the same time, or when the tub itself is leaking. You can check your dishwasher’s build year with our free appliance age lookup.

Frequently Asked Questions

How do I clear F11 on my Miele dishwasher?

Clean the filter combination and the drain pump cover, check the drain hose and sink connection, then switch the machine off for 30 seconds and run a short program. If F11 returns, the drain pump or non-return valve likely needs replacing.

Is it safe to use a Miele dishwasher with F70?

No. F70 means water is in the base pan. Close the water supply, check for leaks and have the source found before running another cycle.

How much does Miele dishwasher repair cost?

Most Miele dishwasher repairs in the Houston area cost between $200 and $500, with circulation pump replacement at the higher end. Filter and blockage problems cost nothing beyond the service call if you need us to diagnose them.

Why does the same code keep coming back after a reset?

A reset clears the message but not the cause. If a code reappears on the next cycle, the underlying part — usually a pump, valve or sensor — needs repair.

Need Help With a Miele Fault Code?

GIR Appliance Repair services Miele dishwashers, ovens, washers and dryers across Houston, The Woodlands, Spring, Kingwood, Humble and Conroe, often the same or next day. See our Miele appliance repair page and dishwasher repair service, or call or text (346) 625-4289. The $75 service call is applied toward your repair.

Ready to schedule your repair?

We serve The Woodlands, Kingwood, Spring, Humble & greater Houston. Call or book online.

📞 (346) 625-4289
GIR Appliance Repair technician
GIR Appliance Repair
Same-day appliance repair in The Woodlands, Kingwood, Spring, Humble & Houston. Licensed & insured. Call (346) 625-4289.

More Appliance Repair Guides

(346) 625-4289Tap to Call · Same-Day