Technician Answers

Frigidaire FPHD2491KF0 dishwasher touch panel stays off and won’t start

Answered by GIR Technician, GIR Appliance Repair · November 14, 2026
❓ The question
Frigidaire Dishwasher Model FPHD2491KF0

“TOUCH PANEL START NOT WORKING STAYS OFF”

Asked by PAUL from CA · November 14, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Paul,

A dishwasher with a dead touch panel is frustrating, because it gives you nothing to go on. On your Frigidaire Professional FPHD2491KF0 it usually comes down to a few things, and you can rule out the simple ones yourself.

Start with power and a reset

  1. Check the breaker and any wall switch. Many dishwashers are wired to a switch next to the sink (often beside the disposal switch) that gets bumped off. Also look for a tripped breaker or a GFCI outlet under the sink that needs resetting.
  2. Do a hard reset. Turn the dishwasher’s breaker off for about 5 minutes, then back on. A power surge can lock up the electronics, and this clears it.
  3. Try the panel the right way. Your model has hidden controls on the top edge of the door. Open the door, press a cycle and Start, then close the door firmly within a few seconds. If the door isn’t fully latched, the cycle won’t begin.

If the panel still won’t light at all

Then the dishwasher is either not getting power or the electronics have failed. With the breaker off, remove the lower kick panel and check the wiring junction box at the front right corner underneath. Loose or burnt wire nuts there are a common cause. If you’re comfortable with a multimeter, turn the power back on carefully and confirm about 120 volts at that box; if you’re not, this is a good point to have a technician check it.

If power is reaching the dishwasher but the panel stays dark, the most likely culprits are:

  • Main control board – the most common failure on this generation of Frigidaire dishwashers. A board that gets power but shows no lights, even after a reset, points here.
  • Touchpad (user interface) – if some lights come on but pressing Start does nothing, or only certain buttons respond, the touchpad or its ribbon cable is more likely. Unplug and reseat that ribbon cable first; a loose connection there is a free fix.

I’ve listed both parts below so you can check price and availability right there. As a rough idea, a control board often runs about $100–$250 and a touchpad roughly $50–$150, depending on the supplier.

Repair or replace?

This model is getting older, so if the board is the problem, weigh that cost against a new dishwasher. Our repair-or-replace calculator can help you decide. A similar dead-panel case on a different brand is covered here: KitchenAid dishwasher panel won’t light.

Let me know what you find at the junction box or after the reset, and I’ll help you narrow it down. Just send a follow-up.

– The GIR Technician

🔧 Part needed
Main control board
Fits Frigidaire FPHD2491KF0

If power reaches the dishwasher but the panel stays completely dark after a reset. We'll match the exact part # to your FPHD2491KF0.

Touchpad / user interface
Fits Frigidaire FPHD2491KF0

If some lights come on but Start or certain buttons don't respond, even after reseating the ribbon cable. We'll match the exact part # to your FPHD2491KF0.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day