Technician Answers

Whirlpool WDFS3R4NBSAU dishwasher F8 E4 flood code keeps coming back after drying out

Answered by GIR Technician, GIR Appliance Repair · November 15, 2026
❓ The question
Whirlpool Dishwasher Model WDFS3R4NBSAU Age: Under 1 year

“It will turn back on and run a cycle and complete it fine however it later starts beeping with the error message again.”

We followed your suggestion and left the dishwasher to dry out for 48 hours. After this, it turned back on and the error message and beeping had stopped.

It then ran a couple of cycles without any issues. However, approximately an hour after one of the cycles had finished, it randomly started beeping again and displaying the error message.

There were no suds or signs of water leaking underneath the dishwasher when the cycle finished. The issue seems to be occurring intermittently, as the dishwasher will turn back on normally, run a few cycles without any problems, and then randomly start beeping and displaying the error message again.

Given that the issue keeps returning despite allowing the dishwasher to dry out, we're concerned there may be an underlying fault that needs to be investigated.

Asked by Megan · November 15, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Megan,

Thanks for drying it out and testing it the way I suggested in my earlier answer about the F8 E4 code. That result actually tells us a lot. If it was only leftover suds, the code would have stayed gone once the base dried. Coming back an hour after a clean cycle, with nothing on the floor, points to a small leak inside the machine that drips into the base tray slowly and lifts the flood float again after the cycle is over.

What usually causes this

  • A slow drip inside the cabinet, from a hose connection, the pump or sump seal, or the water inlet valve. These leak into the base tray, not onto your floor, so you never see it.
  • Water getting past the door, from the door seal or the lower door gasket. This often shows up as a trickle at the bottom corners.
  • Rinse aid overflowing. If the rinse aid dispenser was overfilled or its cap isn’t sealing, it can foam and slip a little water past the door.

Quick checks you can do without opening it up

  1. When the code comes back, write down exactly what’s on the display and what time it is compared to the end of the cycle. If it’s a different code from F8 E4, that changes the diagnosis.
  2. Check the rinse aid cap is fully closed and wipe up any spilled rinse aid around it.
  3. After a cycle, run a dry paper towel along the bottom edge of the door and the lower corners of the tub. Damp towel = door seal area.
  4. Take a short phone video of the display and a couple of photos of the door seal. They’ll be useful for the warranty visit.

Let Whirlpool’s warranty handle it

Since your dishwasher is under a year old and the fault keeps coming back, I agree with you: something needs fixing, and it should be fixed under warranty. Please don’t take off the kickplate or panels yourself. Tracking down a slow internal leak is a job for the warranty technician. Contact Whirlpool Australia, give them your model (WDFS3R4NBSAU) and serial number from the label on the edge of the door, and tell them it’s an intermittent flood sensor fault that keeps returning with no suds present after a full dry-out.

Until then, keep the tap under the sink turned off between loads if you can. It’s a cheap way to stop any slow leak from the inlet valve.

If the technician finds something, or you’d like help reading what they tell you, feel free to send a follow-up. Good luck, and I hope it’s an easy fix!

Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day