Technician Answers

Kenmore 106.56832604 refrigerator stops cooling and won’t restart until it rests

Answered by GIR Technician, GIR Appliance Repair · November 16, 2026
❓ The question
Kenmore Refrigerator Model 106.56832604 Age: Over 12 years

“Cools for a day or two then won't restart after it shuts off.”

This problem started 5 days ago started running for awhile and shutting off and restarting. Then it didn't start again after 2 or 3 days of working. Cleaned it good left off for 30 minutes or so now seems to be working for the last 12 hours. Is there something going out? Can it be fixed?

Asked by Rose from NE · November 16, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Rose,

That on-again, off-again pattern is frustrating, but it’s also a useful clue. Your Kenmore 106.56832604 is built by Whirlpool, and when one of these runs for a while, shuts down, then starts working again after it’s been cleaned and rested, it usually means the compressor is getting too hot and its safety overload is cutting it off. The good news: the common causes are fixable and not expensive.

What’s most likely going on

  • Dirty condenser coils. If the cleaning you did included the coils underneath and the bottom grille, that alone may be why it’s running again. Dust traps heat and the compressor overheats.
  • Condenser fan motor. This small fan sits near the compressor at the bottom back. If it’s stuck, slow, or stops, heat builds up the same way and the fridge quits after a day or two.
  • Start relay/overload. This little plug-on part on the side of the compressor wears out on older fridges. A failing one often makes a click every few minutes while the compressor stays silent.

What I’d check next

  1. Unplug the fridge, pull it out, and take off the thin back panel at the bottom. Vacuum or brush the coils and around the compressor if you haven’t already.
  2. Plug it back in and watch the condenser fan when the compressor is running. It should spin freely and steadily. With power off, give the blade a flick: it should turn easily, not feel stiff.
  3. Next time it quits, notice whether the inside light is still on. If the light is on but it’s quiet and warm, listen near the compressor for a click every few minutes. That points to the relay/overload.
  4. Leave a few inches of space behind and above the fridge so it can breathe.

If the fan stops or drags, replace the condenser fan motor. If the fan runs fine and you still hear clicking with no hum, replace the start relay/overload. I’ve listed both parts below. You can check price and availability right there. Both are usually under about $60 to $90 as a rough range. There’s a similar case here: Kenmore fridge clicking when the compressor starts.

Repair or replace?

At 12+ years, a fan or relay is still worth fixing. If those check out and it keeps shutting off, the compressor itself may be getting weak. That’s technician-only sealed-system work, and on a fridge this age it usually costs more than it’s worth. Our repair-or-replace tool can help you weigh it.

Let me know what you find with the fan and the clicking and I’ll help you narrow it down. Just send a follow-up.

🔧 Part needed
Condenser fan motor
Fits Kenmore 106.56832604

If the condenser fan is stopped, stiff, or slow. We'll match the exact part # to your 106.56832604.

Compressor start relay/overload
Fits Kenmore 106.56832604

If the fan runs fine but the compressor clicks every few minutes without starting. We'll match the exact part # to your 106.56832604.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day