Technician Answers

GE GTX18ESSJ0WW electric dryer takes three cycles to dry a load

Answered by GIR Technician, GIR Appliance Repair · November 10, 2026
❓ The question
GE Dryer Model GTX18ESSJ0WW Age: 8–12 years

“It is taking 3x in the dryer to dry the clothes. What could be wring”

The clothes aren’t dry after the first cycle. It took me 3x to dry the clothes completely. Did not overload the dryer. Set it on high heat. The dryer is either 11 or 23 years old according to the age finder

GE Dryer photo 1 from the question
Asked by Susan from MD · November 9, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Susan,

Three cycles for one load is frustrating, and it burns a lot of power too. Thanks for the photo of the label. Your model is a GTX18ESSJ0WW (that’s a zero, not the letter O), and it’s an electric dryer. On the age: the serial starts with LF, and in GE’s code the second letter F means either 2003 or 2015. A label with a QR code like yours points to the newer date, so your dryer is most likely about 11 years old.

Start with the airflow

Most slow drying comes from a blocked vent, not a broken part. Here’s what I’d check first:

  1. Lint screen. Clean it, then rinse it under the tap. If water beads up and won’t go through, dryer-sheet film is blocking it. Scrub it with dish soap and a soft brush.
  2. Vent outside. Run the dryer and go to the outside flap. You should feel a strong, warm blast of air. If it’s weak, the vent run is clogged with lint.
  3. Hose behind the dryer. Unplug the dryer, pull it out and check the hose for crushed spots or packed lint. Clean the whole run with a vent brush kit. Foil or vinyl hose should be swapped for semi-rigid metal.

A clogged vent is also a fire risk, so this is worth doing even if it turns out not to be the whole problem.

Is it actually getting hot?

Run a timed high-heat cycle and feel the clothes after 10 minutes. If the air is only lukewarm:

  • Check the breaker. An electric dryer uses a double breaker. If one half trips, the drum still turns but you get little or no heat. Flip it fully off and back on.
  • Heater. With the breaker off, a handy person can test the heater with a multimeter. It should read low ohms. If it reads open, it needs replacing.
  • Cycling thermostat. If the heater is good but heat cuts out early and the clothes stay damp, the cycling thermostat is a common cause on this model.

I’ve listed the exact parts for your model below, so you can check price and availability right there. Always turn the breaker off before opening any panel.

Repair or replace?

At around 11 years old, a vent cleaning or a heater or thermostat swap is a reasonable fix on a simple dryer like this. Rough parts cost is usually under $100. If you want a second opinion, try our repair-or-replace tool.

Let me know what you find at the outside vent and whether the air feels hot. If it’s still slow, send a follow-up and we’ll narrow it down.

🔧 Part needed
Heater assembly (mica heater & housing)
Part # WE11X20397 Fits GE GTX18ESSJ0WW

If the vent and breaker check out and the air coming out is only lukewarm or cool.

Cycling (outlet) thermostat
Part # WE4M216 Fits GE GTX18ESSJ0WW

If the heater tests good but heat keeps shutting off too early in the cycle.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day