Technician Answers

Kenmore 110.22102311 washer: lid locks, then unlocks and start light blinks

Answered by GIR Technician, GIR Appliance Repair · November 18, 2026
❓ The question
Kenmore Washer Model 110.22102311

“start light turns green, lid locks, and then lid unlocks and starts blinking”

Its happened a couple of times before but i unplugged washer and that fixed it and it would run. Thought the last load might have been unbalanced or lock wasnt engaging, but lock engages the first time and then starts flashing. When light is blinking start button wont do anything.
Ser C44920190

Asked by Rae from AL · November 18, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Rae,

That’s a frustrating one, especially when unplugging it “fixes” it for a load or two and then it comes right back. What you’re describing—lid locks, then unlocks and the start light blinks and won’t respond—is the washer telling you it hit a fault during its start-up checks. On these Whirlpool-built Kenmore top loaders (the 110 prefix means Whirlpool made it), the most common reason by far is the lid lock not reporting back to the control that it’s locked, even though you can hear it engage.

What I’d check first

  1. Reset it properly. Unplug it for a full 5 minutes, not just a few seconds, then try a small, evenly spread load.
  2. Look at the lid strike. That’s the little plastic tab on the underside of the lid that pushes into the lock. If it’s cracked, loose or bent, the lock can grab it once and then lose it. Make sure the lid sits fully flat, too.
  3. Watch what happens before it unlocks. Does water start coming in, or does the basket turn a little first? If it unlocks before any water or movement, that points hard at the lid lock. If it fills for a long time first, check that both faucets are fully open and the inlet hose screens aren’t clogged—a slow fill can also stop the cycle.
  4. Check the wiring at the lock. With the washer unplugged, lift the top (it’s held by clips or screws near the back) and look at the harness going to the lid lock. Wires can rub through or a connector can work loose where the top hinges.

The most likely fix

If the strike looks good and the wiring is fine, I’d replace the lid lock assembly. Inside it there’s a small switch that tells the control “I’m locked”; when that switch gets worn it works sometimes and not others, which matches exactly what you’re seeing. It’s a fairly easy DIY job—a few screws and one connector—and the part usually runs roughly $40–$90. I’ve listed it below; we’ll match the exact part number to your model.

About the age

I don’t want to guess a date from that serial alone. The easiest way to confirm the age is the tech sheet tucked behind the console or under the top—it’s often printed with a date code. If you send me a photo of the data tag (under the lid) and that sheet, I’ll read it for you.

If you try the lid lock and it still unlocks and blinks, tell me exactly what it does before it stops and send a follow-up—I’m happy to help you narrow it down.

— The GIR Technician

🔧 Part needed
Lid lock assembly
Fits Kenmore 110.22102311

If the lid strike and wiring look fine but it still unlocks and blinks. We'll match the exact part # to your 110.22102311.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day