Technician Answers

Kenmore dryer power cord has bare inner wires showing at the back: is it safe to use?

Answered by GIR Technician, GIR Appliance Repair · November 19, 2026
❓ The question
Kenmore Dryer

“I want to know if this cord going into this dryer is safe”

I just got this dryer from Facebook marketplace today. It runs fine and the guy gave me a 1 month warranty. I'm just a little concerned about the wire that plugs into it. I'm not sure if it's supposed to look like this or not. I don't want to start a fire. He said that it's fine and the wires are intact.

Kenmore Dryer photo 1 from the question
Asked by Zak from MO · November 19, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Zak,

Good call checking. From your photos, no, that cord isn’t installed the way it should be. No need to panic, but I’d fix it before another load.

What’s wrong in the photo

Right where the cord goes into the back of the dryer, the black outer jacket has been cut back. The inner wires (I can see red and green, plus the white filler) are sticking out bare, past the jacket and right at the hole in the metal panel. There’s also no strain relief, which is the clamp that grips the cord at that hole.

  • Only the thin wire insulation is protecting those wires from the edge of a sheet-metal hole.
  • With no clamp, any tug on the cord pulls on the screw terminals inside. That can loosen a connection, and loose connections get hot.

The wires may be intact today, but a dryer shakes and gets moved, so this setup can wear through or work loose. On a 240-volt circuit, that’s how scorched terminal blocks and fires start.

What I’d do

  1. Unplug the dryer and leave it unplugged until the cord is fixed.
  2. Take the small cover off the terminal block (the plate just above where the cord goes in, usually one screw). Look for any black or melted spots on the block or the wire ends. If so, replace the block too.
  3. Check your wall outlet. A 3-slot outlet needs a 3-wire cord, and a 4-slot outlet needs a 4-wire cord. Your cord looks like a 4-wire.
  4. Install a new 30-amp dryer cord that matches your outlet, plus a new strain relief clamp. They’re cheap, roughly $15–35 for the pair, and most hardware stores carry them.
  5. Follow the label next to the terminal block. White (neutral) goes to the center terminal and green goes to the green ground screw. On a 4-wire cord, the little ground strap between the center terminal and the cabinet has to be removed. On a 3-wire cord, it stays in place. The jacket should end inside the clamp, with no bare inner wires showing outside the dryer.

If you’d rather not do it yourself, ask the seller to fix it under the warranty he gave you, or have a local appliance tech or electrician do it. It’s a quick job. I’ve listed the cord below, and we’ll match it to your model once we know it.

Finding your model number

On most Kenmore dryers, the tag is on the frame inside the door opening. The model looks like 110.xxxxxxxx or 417.xxxxxxxx. Send it over and I’ll confirm the right cord and clamp.

Once the cord is redone, it should be safe to use. If anything looks scorched or you get stuck, send a follow-up with a photo and I’ll take a look.

🔧 Part needed
Dryer power cord, 30A (3- or 4-wire to match your outlet) with strain relief
Fits Kenmore

Replace now — the jacket is cut back and there's no strain relief clamp. We'll match the exact part # to your Kenmore dryer model.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day