Technician Answers

GE Profile JGP963SEF1SS gas cooktop keeps clicking on one burner even with the knob off

Answered by GIR Technician, GIR Appliance Repair · November 12, 2026
❓ The question
GE Cooktop Model JGP963SEF1SS Age: Over 12 years

“How can I get the clicking resolved in my cooktop ?”

When my gas is turned on , the cooktop on one burner is clicking, I have cleaned it and all areas on top pieces of burner and dried all areas, I turned off the breaker because the clicking is continuous on one of the 5 burners , even when the gas is off, any ideas? this is a GE Profile about 24 years old

Asked by Doug from SC · November 12, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Doug,

Non-stop clicking with the knob off is annoying, and you did the right thing by flipping the breaker. Cleaning and drying the burner was a good first step too. Since the clicking keeps going even with the gas off, though, the problem probably isn’t up at the burner. It’s most likely in the switch that tells the cooktop to spark.

Why it keeps clicking

Each knob on your JGP963SEF1SS sits on a gas valve, and each valve has a small spark switch clipped onto it. When you turn a knob to LITE, that switch closes and the spark module fires the igniters. If one switch gets stuck closed or shorts out, the module thinks that burner is being lit and clicks forever. On a 24-year-old cooktop this is very common. Boil-overs and cleaning water drip down the valve stem, and over the years the contacts corrode or crack.

The less likely cause is the spark module itself failing and firing all the time, no matter which switch is closed.

What I’d try, in order

  1. Let it dry out completely. If any water got down around the knobs while you were cleaning, leave the breaker off for a day or two, or point a hair dryer on low at the knob area for a few minutes. Then turn the power back on. Sometimes the clicking just stops.
  2. Work the knob. With the power on and the gas off, turn the knob on the clicking burner to LITE and back to OFF a few times. Do the same with the other four knobs. If the clicking changes or stops when you move one of them, that knob’s switch is the problem.
  3. Check the switch. Turn off the breaker and shut off the gas first. Then pull the knobs and lift the cooktop to reach the valves. Look for a cracked, burnt or wet switch on the valve you suspect. With the wires off, a switch should show an open circuit on a meter when its knob is OFF. If it shows continuity with the knob off, it’s bad.
  4. If every switch tests open and it still clicks, the spark module is the likely culprit.

I’ve listed both parts below so you can check price and availability. A spark switch is usually a cheap part, roughly $15–40. A module typically runs more, roughly $50–120. Both are reasonable repairs on an older cooktop that otherwise works well. If you smell gas at any point, leave the house and call your gas company from outside.

If you’d like a second opinion on what you find under the cooktop, send a follow-up. There’s also a similar case here: igniters that keep clicking after the burner lights. I’ve answered your fridge drawer question separately.

Good luck, and let me know how it goes!

🔧 Part needed
Burner valve spark switch
Fits GE JGP963SEF1SS

If the clicking stops or changes when you turn one knob, or that switch shows continuity with the knob off. We'll match the exact part # to your JGP963SEF1SS.

Spark module
Fits GE JGP963SEF1SS

If every valve switch tests open but it still clicks non-stop. We'll match the exact part # to your JGP963SEF1SS.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day