Technician Answers

LG DLEX3700V dryer runs but no longer heats on the regular cycle

Answered by GIR Technician, GIR Appliance Repair · November 11, 2026
❓ The question
LG Dryer Model DLEX3700V

“regular dyer selection no longer heating”

I have the matching washer bought at the same time , not sure if it 2009 or 2019, serial no.: 906KWDJ1P922.

We are ready to replace both washer and dryer if needed.

Asked by GERI from CA · November 11, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Geri,

A dryer that tumbles but blows cold air is one of the most common calls we get, and the good news is it’s usually a fairly inexpensive fix on the DLEX3700V. Here’s what I’d check, easiest first.

How old is the set?

LG serial numbers start with the year and month: the first digit is the last digit of the year and the next two are the month. Your washer’s serial starts with 906, so it was made in June of either 2009 or 2019. This dryer model wasn’t on the market back in 2009, so a matching set points to 2019, about 7 years old. That’s well within the age where repairing a no-heat problem makes sense.

Quick checks first

  1. The breaker. An electric dryer runs on a double 240V breaker. If only one half trips, the drum and display still work but there’s no heat. Flip that breaker fully off, then back on, and try a Normal cycle on high heat.
  2. Try another cycle. Run a timed dry on high heat for 5 minutes. If no cycle heats, keep going below.
  3. The vent. Clean the lint screen, then pull the dryer out and check the flex duct behind it and the outside flap. A blocked vent is the number-one reason the safety parts below fail. If the display ever shows a d80, d90 or d95 code, that’s the dryer warning you about vent blockage.

The two most likely parts

If the breaker and vent check out, the problem is almost always in the heater housing at the back. Unplug the dryer before you open anything, then remove the back panel and test with a multimeter:

  • Thermal fuse / high-limit on the heater housing. It should show continuity. If it’s open, it has blown and has to be replaced (it doesn’t reset). Clean the vent before you put the new one in, or it can blow again.
  • Heating element. Test across its two terminals. It should read roughly 10 ohms. An open reading (no continuity) means the coil has broken.

I’ve listed the exact parts for your model below, so you can check price and availability right there. Either one is far cheaper than a new dryer.

Repair or replace?

For a 2019 dryer with a no-heat problem, I’d repair it. Our repair-or-replace calculator can help you compare.

If you test those parts and they’re good, or some cycles heat and others don’t, send a follow-up with what you found and I’ll help you take the next step.

Take care,
GIR Technician

🔧 Part needed
Thermal fuse (high-limit)
Part # 6931EL3003D Fits LG DLEX3700V

If the breaker and vent are fine and the fuse on the heater housing shows no continuity.

Heater assembly (heating element)
Part # 5301EL1001J Fits LG DLEX3700V

If the thermal fuse tests good but the element reads open instead of about 10 ohms.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day