Technician Answers

Hotpoint RAS200DM3WW drip pans and coils don’t match or sit level — which ones fit?

Answered by GIR Technician, GIR Appliance Repair · November 15, 2026
❓ The question
Hotpoint Oven / Range Model RAS200DM3WW Age: Under 1 year

“Mgmt at my hud bldg difficulty in finding compaticble drip pans and coils 1- 8" 3-6" for small 20ft stove stove”

He gave me drip pans but they didnt fit, when I returned them he said, oh yea, your stove needs different ones, Ill order a whole set with the coils units as well. Time went by, months, and finally a new asst installed them-3 were one kind of drip pan, 1 was different, the coils were all nice looking and alike but didn't match the originals which had center points for heat regulations, I like these better, I spent over an hour with photos with AI and the large coil was twistedinto the difficult drip pan , the tiny hole was bent , later after taking each one out I realized one small 6 inch was totally different. So this couldn't be a matching set. I fixed Hammered the bent piece, the big one, but it still bounces a bit not level, same for one other, I finally got model number and serial number, and went to look for parts and got very confused measuring and actual diameter and I just want to know what to tell the superintendent.. I just want them level and matching.Is porcelain poss

Asked by Lilly from CA · November 14, 2026
GIR Technician
GIR TechnicianAppliance technician · GIR Appliance Repair, The Woodlands, TX
✓ Technician answer

Hi Lilly,

That sounds frustrating, especially after waiting months. You’re right that a mixed set will never sit level. The good news is that your Hotpoint RAS200DM3WW has a short, clear factory parts list, so you can hand your superintendent the exact part numbers.

What your range takes

Your 20″ range has four burners: one 8″ and three 6″. The factory parts list for your model shows:

  • 6″ drip bowl (chrome): WB31K10265 (you need 3)
  • 8″ drip bowl (chrome): WB31K10266 (you need 1)
  • 6″ surface burner with sensor: WB31X46067 (you need 3)
  • 8″ surface burner with sensor: WB31X46066 (you need 1)

The “center points” you noticed on your original coils are the temperature sensors. Your range was built with sensor burners, so I’d go back to the factory sensor burners rather than keep a mix of other coils. They’re what the range was designed and safety-tested with.

Why they bounce and won’t sit level

  • Wrong or bent bowl. If a bowl isn’t the right one or has been bent, the burner sits crooked. Hammering it straight rarely brings it back flat. Bent bowls should be replaced.
  • Burner not fully plugged in. With the burner off and cool, the two prongs should push all the way into the plug-in socket, and the burner should rest flat on its support. If it only goes in partway, the bowl’s hole may be the wrong size or bent.
  • Mixed burners. Coils from different makers can have slightly different legs and heights, so even the right bowls won’t fix a mismatched burner.

Before anyone pulls burners or bowls out, the burners should be off and completely cool.

What to tell the superintendent

Ask for a matched set ordered by the model number RAS200DM3WW, using the four part numbers above. That’s far easier than measuring, because sizes measured at home are often a little off. On porcelain: the factory list for your model only shows chrome bowls. If they want porcelain, they should only order bowls sold as a fit for your exact model number and check that they match the chrome ones in size and in the cutout for the plug.

If anything still sits crooked after the new set is in, send a follow-up and tell me which burner it is. I’m happy to help you sort it out.

— GIR Technician

🔧 Part needed
6" drip bowl (chrome)
Part # WB31K10265 Fits Hotpoint RAS200DM3WW

You need 3 for the small burners. Replace any that are bent or don't match.

8" drip bowl (chrome)
Part # WB31K10266 Fits Hotpoint RAS200DM3WW

You need 1 for the large burner, especially if it's bent or the burner won't sit level.

Want us to get this part for you? We source genuine parts through our supplier network. Send a quick request and we'll email you the current price and availability, usually within one business day. No obligation.
Still stuck, or is your situation different?Ask your own question and a technician will answer it for free.
💬 Ask a Follow-Up Question
(346) 625-4289Tap to Call · Same-Day